How to Read and Program Your Sprinkler Timer
Nearly every sprinkler timer, old or new, comes down to five settings: the clock, the watering days, the start times, the run time for each zone and a seasonal adjust. Get those right, keep the rain sensor connected, and most controllers will water well and stay inside Miami-Dade's rules.
UF/IFAS Extension describes these same basic settings for all residential timers, whatever the brand. The buttons differ; the logic does not. Keep your owner's manual handy (most are online by model number) and walk through the steps below.
Where to find sprinkler system timer manuals
Use the manufacturer's support site and the exact model number, not just the brand on the door. A controller family can include different indoor, outdoor, battery and Wi-Fi versions with different menus.
- Find the model label. Look on the faceplate, inside the ordinary user door or on an accessible exterior label. Photograph the model and station count. Do not remove a mains-wiring cover to find it.
- Start with official support. Search for the model plus "owner manual" or "programming guide" on the maker's website. [Hunter support](https://www.hunterirrigation.com/support) and [Rain Bird's residential timer directory](https://www.rainbird.com/homeowners/products/timers-controllers) are manufacturer resources, not independent recommendations. Other brands have their own support libraries.
- Match the controls and revision. Check that the manual pictures and dial positions match your timer. For a Wi-Fi controller, the hardware guide and app help may be separate, so use both when applicable.
- Save the official PDF or page. Keep the manual and photos of your working settings together. Avoid download sites that ask you to install software just to read a manual.
Can I program a sprinkler timer without the manual?
Usually you can identify the basic clock, days, start times and station run times from the labels. Record the current settings first, change one item at a time and use the steps below as a checklist, not model-specific button instructions. Do not factory-reset an unfamiliar timer: you may erase station settings or pump and master-valve configuration. If the controls do not match this guide, stop and find the model manual or book sprinkler controller repair.
Why does the manual show several start times?
On many program-based timers, each start time repeats all stations assigned to that program. You normally do not need a new start time for each zone. Some station-based timers work differently, so confirm which design your model uses before deleting entries. Review every program, including unused B and C programs, for duplicate starts.
Know the vocabulary
- Zone or station: one valve and the heads or drip it feeds. The controller runs zones one after another.
- Program: a set of days, start times and run times. Most timers have A, B and C programs.
- Start time: when a program begins. It starts the first zone; the others follow in order. It is not a start time for each zone.
- Run time: how long each zone runs.
- Seasonal adjust or water budget: a percentage that scales every run time at once.
- Sensor input: where the rain or soil moisture sensor connects.
Step 1: set the clock and date
After any outage, check the time and date first. A clock that is off by twelve hours can move a 5 a.m. run to 5 p.m., or into the hours the county does not allow. Many older timers lose their settings when power fails, so write your program down or take a photo of each screen.
Step 2: set your watering days
Choose the custom or day of week option and pick your two days. Under the county rules, odd-numbered addresses water Wednesday and Saturday, even-numbered addresses Thursday and Sunday. UF/IFAS notes the custom day option is the one to use during water restrictions. Avoid odd or even day and interval settings; they will drift off your allowed days. The Miami-Dade watering restrictions guide has the full rules.
Step 3: set one start time
Pick one start time early in the morning. EPA WaterSense advises against midday watering, when more water is lost to evaporation. Then add up every zone's run time and make sure the whole program finishes before 10 a.m. The most common accidental violation is a long program that started at 7 a.m. and is still running at 10:30.
Check that there are no extra start times. Many timers ship with several, and a second or third start time repeats the whole program, doubling or tripling the water.
Step 4: set run times by zone type
Run times should match what each zone actually puts down. UF/IFAS lists typical rates: spray nozzles about 0.75 to 2 inches per hour, rotors about 0.25 to 1 inch per hour. Hunter (manufacturer) rates its MP Rotator nozzles at about 0.4 inch per hour, so check the nozzle type too. So a spray zone may need 15 to 20 minutes to apply what a rotor zone needs 45 minutes or more for.
The reliable way is a can test, which UF/IFAS describes and EPA WaterSense also suggests: set straight-sided cans in a zone, run it 15 minutes, average the depth and multiply by four for inches per hour. Then set run times to deliver about 1/2 to 3/4 inch for lawn zones.
UF/IFAS also cautions that runs over about an hour tend to push water below the roots on sandy soils. If a rotor zone needs that long, split it into two shorter starts a few hours apart within the allowed hours.
Step 5: use the seasonal adjust
Instead of changing every zone each season, change the percentage. UF/IFAS gives the example of a 60 minute zone set to 75% running 45 minutes. In Miami, a lower percentage suits the wet season and the cooler months; bring it back up for the hot, dry spring. Our seasonal sprinkler schedule covers when to change it.
Step 6: use a second program for special zones
Program B is useful for drip zones, which may run at any time under the county rules, and for new sod or plants, which get extra days for their first 90 days. Put those zones on program B and leave everything else on A. Remember to clear program B when new plantings are established.
Step 7: check the sensor setting
Most timers have a sensor switch or menu with "active" and "bypass." It should be on active. A wired rain sensor, as Hunter's installation guide (manufacturer) explains, breaks the circuit to the valves after rain while the timer keeps running. Florida law requires a working shutoff device on automatic systems, and a bypassed sensor lets the system water in a storm.
Reading the display
- A blinking time or "12:00": power was lost. Reset the clock and check the program.
- A sensor or umbrella icon, or "off": the rain sensor is stopping watering, as it should after rain.
- A station number flashing or "fault": often a wiring or solenoid problem on that zone.
- "Rain delay": watering paused for a set number of days.
Test what you set
Use manual run to start each zone for a minute or two and confirm the right area waters. The county allows test and repair runs outside your days once a week, up to 10 minutes per zone, with someone present.
When the timer is the problem
If your controller loses its program, has dead stations or will not accept a custom day schedule, it may need controller repair or replacement. Wi-Fi controller dropping offline or skipping runs? See smart sprinkler controller not working. If you would like a controller that adjusts run times on its own, see how smart irrigation works and our smart irrigation systems service. We also handle seasonal controller adjustments as part of maintenance plans.
Sources
Rules and figures in this guide come from the official sources below, plus manufacturer documents where marked. Rules change, so check the source before you rely on a date or a number.
- Hunter Industries: controller programming and support (manufacturer)
- Rain Bird: residential timers and controllers (manufacturer)
- UF/IFAS AE220: Operation of Residential Irrigation Timers
- UF/IFAS LH025: Watering Your Florida Lawn
- Miami-Dade County: Outdoor water restrictions
- Florida Statutes 373.62: Water conservation; automatic sprinkler systems
- U.S. EPA WaterSense: Watering tips
- Hunter: MP Rotator zoning and precipitation rates (manufacturer)
- Hunter: Wired Rain-Clik installation guide (manufacturer)