Florida Rain Sensor Law: What Miami Homeowners Need
Florida law requires every automatic landscape irrigation system to have working technology that stops it when there has been enough rain or the soil is moist enough. A rain sensor, a soil moisture sensor or a weather based smart controller can meet that requirement, but only if it is installed, maintained and actually connected.
The rule is Florida Statutes section 373.62. It has applied to all automatic systems in the state since 2010, not just new ones, and Miami-Dade's landscape code and the City of Miami Beach code repeat the requirement locally. Here is what it means in practice.
What the law says
Section 373.62 has two parts that matter to homeowners:
- Anyone who buys or installs an automatic system must properly install, maintain and operate technology that interrupts or prevents irrigation during periods of enough rainfall or soil moisture.
- A licensed contractor working on an automatic system must test the shutoff device first, and install or repair it if it is missing or not working, before doing other work on the system.
The second point surprises people. A licensed contractor who comes to fix a broken head should check the sensor. If yours is missing or dead, expect that to be part of the visit.
What counts as a shutoff device
UF/IFAS Extension lists three types that satisfy the law:
- Rain sensors. The most common and the least expensive. Most use small disks that swell when wet and press a switch that stops watering. They dry out and reset on their own.
- Soil moisture sensors. A probe buried in the root zone measures soil water and skips runs when the soil is wet. UF/IFAS recommends placing the probe in the zone that dries out first.
- Weather based (ET) smart controllers. These adjust watering from local weather data and skip or shorten runs after rain.
Our guide to smart controllers versus timers compares the last two in more detail.
Where a rain sensor should go
Placement decides whether a sensor works. Hunter's installation guide (manufacturer) calls for a spot open to unobstructed rain but out of the path of sprinkler spray, and UF/IFAS recommends mounting it:
- Where it is open to rain from every direction.
- Away from sprinkler spray, which would trip it every watering day.
- Away from roof runoff, gutters and overhanging trees, which add or block water.
- Within reach for testing and cleaning.
Wireless sensors make good placement easier. UF/IFAS notes they can work at distances up to about 300 feet from the controller, so you are not limited to the wall where the timer hangs.
How to test yours
UF/IFAS recommends testing at least once a year. It takes five minutes:
- Turn on one zone manually at the controller.
- Spray the sensor with a hose, or press the test button if it has one, as Hunter (manufacturer) suggests for its sensors.
- Watch the zone. A disk type sensor should stop it within a few minutes. Hunter says its wired sensor shuts the system down within the first few minutes of rain.
- If the zone keeps running, check that the sensor is connected and not in bypass mode, then look at the wiring.
Most rain sensors interrupt the common wire between the controller and the valves. If someone cut it out of the circuit to stop a nuisance shutoff, the system will run in a storm. A bypass switch left on does the same thing.
Settings and upkeep
- Set point: UF/IFAS recommends setting the sensor to shut off at the smallest rainfall setting possible, and no more than 1/4 inch.
- Disks: the absorbent disks wear out. UF/IFAS suggests replacing them at least every two years.
- After storms: check the mount and the wire. Wind and falling branches knock sensors loose more often than people think.
Why it matters in Miami
Miami gets most of its rain in the wet season, which the National Weather Service in Miami puts at about May 15 to October 15, with 60 to 70 percent of the year's rain, often in short heavy thunderstorms. A system without a working sensor waters on schedule the next morning anyway, which wastes water, raises the bill and keeps St. Augustine too wet. EPA WaterSense warns that overwatering leads to weeds, disease and fungus.
The county's two day schedule still applies with a sensor. The sensor just stops a scheduled run when the yard does not need it. Read the Miami-Dade watering restrictions for the days and hours.
Soil moisture sensors and watering days
One extra detail: under section 373.62, a property with a monitored soil moisture sensor system can apply for a variance from the day of week limits through its HOA, condo association or utility. The time of day limits still apply. This is mostly relevant to larger properties, and the variance has to be granted. It is not automatic.
Repair or replace?
Rain sensors are simple. If the disks are worn or the cap is cracked, many models can be refreshed. If the sensor is wired wrong, mounted under a tree or missing entirely, it is usually faster to install a new one in a better spot. We test, repair or install rain sensors on every system we service, and we check the controller wiring at the same time so the sensor actually stops the zones. If the controller itself is the problem, our controller repair team can fix that too.
Book a visit if you are not sure your sensor works. We will test it in front of you.
Sources
Rules and figures in this guide come from the official sources below, plus manufacturer documents where marked. Rules change, so check the source before you rely on a date or a number.
- Florida Statutes 373.62: Water conservation; automatic sprinkler systems
- UF/IFAS AE221: Rain Sensors for Irrigation Systems
- UF/IFAS AE437: Soil Moisture Sensor Irrigation Controllers
- UF/IFAS AE442: Smart Irrigation Controllers
- Miami-Dade County Landscape Ordinance (Chapter 18A)
- City of Miami Beach: Water conservation
- SFWMD: Rainy season water management
- NOAA National Weather Service Miami: 2025 rainy season outlook
- U.S. EPA WaterSense: Watering tips
- Hunter: Wired Rain-Clik installation guide (manufacturer)
- Hunter: Rain-Clik not turning sprinklers off (manufacturer)