(786) 496-4049 Contact Us

Sprinkler Wiring Repair in Miami

We find the broken wire, fix it with waterproof splices and get every zone answering the controller again.

  • Miami-Dade local team
  • Over 20 years of experience
  • Clear quotes before any work
  • Lawn and landscape irrigation only
Pop up spray head watering green turf up close

Every valve in your yard is opened by a thin low voltage wire that runs from the controller, usually buried alongside the pipe. When a shovel, a fence post, a root or a corroded splice breaks that path, a zone stops answering, and often several zones go quiet at once.

We test each circuit at the controller, trace the wire path, find the break or short and repair it with waterproof connectors. If the wiring is fine, the fault is at the valve or the controller, and we fix that instead.

Wiring repair includes

  • Circuit tests at the controller for every zone
  • Wire tracing to find cuts, shorts and bad splices
  • Waterproof splice kits and new wire runs where needed
  • Common wire checks when several zones fail together
  • A run of every zone from the controller to confirm

Ask for a free sprinkler wiring repair estimate

Common problems we fix

Free system check on your first visit

Your first visit includes a zone by zone check, so you know exactly where your system stands before you decide on any work.

Book your free system check

Our sprinkler wiring repair process

  1. Inspect

    We run every zone and walk the property to see what the system is really doing.

  2. Diagnose

    We test heads, valves, wiring, pressure and the controller to find the cause, not just the symptom.

  3. Quote

    You get a clear price before any work starts. No surprise fees.

  4. Repair

    We open only the spot where the wire failed, splice it with waterproof connectors or pull a new run, and test the zone from the controller.

  5. Confirm

    We run the zones again and check coverage, so you see the result before we leave.

Serving Coral Gables, Coconut Grove, South Miami, Pinecrest, Kendall, Miami Beach, Doral, Brickell and the rest of Miami-Dade County. See every area we serve

Frequently asked questions

Several zones stopped at the same time. Is that a wiring problem?

Very often. All the valves usually share one common wire back to the controller, so a single cut or corroded splice on that wire can silence several zones at once. A failed controller output can look the same, which is why we test at the panel before anyone digs. Most homeowners are surprised how small the actual break turns out to be. Book a wiring check and tell us which zones went quiet.

Can you find a broken wire without digging up the yard?

Yes. We use a wire tracer and fault locator to follow the buried wire and pinpoint the cut or short from the surface, then dig a small hole right where it is. That protects your sod, beds and pavers and makes the repair faster. Old systems with no map are routine for us. Request a visit and we will track it down.

Why did my zones stop after a fence, pool or landscaping job?

Because buried valve wires are easy to cut and hard to see. Post holes, trenching for lights, new beds and paver base work are the usual culprits, and the damage often shows up days later on the next watering day. We trace the wire through the work area, splice it properly and, if the old route is now under concrete, run new wire around it. It is a common call after renovations, so do not worry about who caused it. Book a repair.

Do you fix splices in wet valve boxes?

Yes, and they are one of the most common faults we find. Miami valve boxes sit in damp soil or standing water, and splices made with tape or plain wire nuts corrode until the valve stops responding or works only some days. We cut back to clean copper and use waterproof, gel filled connectors made for buried irrigation wiring. That turns a repeat problem into a one time fix. Valve checks are part of every tune-up.

Can you add a zone without rewiring the whole system?

Usually. If there is a spare wire in the run, we use it. If not, we can run a new wire to the new valve or, where the controller supports it, use a decoder or similar option that shares existing wire. We check the controller has a free station first so you are not surprised later. Planning a new bed or lawn area? Our sprinkler installation team can design the new zone at the same time.

Is a wiring fault dangerous?

The valve circuit runs on low voltage from the controller's transformer, so a cut zone wire is not a shock hazard like household wiring. It can still damage the controller if a short keeps tripping it, so do not keep running a zone that the controller reports as faulty. Repairs to the 120 volt outlet or circuit that powers the controller belong to a licensed electrician, and we will tell you if that is where the problem is. For the low voltage side, book a repair and we handle it.

Still have a question? Send it to our team with your estimate request and we will answer it on the call.

Get your free estimate

Tell us what is going on with your system and we will get back to you with next steps and a clear price.

CallGet a Free Estimate